- Lightning Link 80 Percent Calculator
- Lightning Link 80 Percent Percentage
- Lightning Link 80 Percent 100
This thing's as slick as owl do! do! No worries about M-16 parts. No machining or drilling on a six hundred dollar gun.
Win casino games. The parts can be made from tool steel, machined with great precision, hardened and tempered with loving care, then polished to a high gloss that your mother would be proud of.
New casino bonus. On the other hand, using only a couple pieces of power hacksaw blade to make the parts from, a dremeJtm tool, hand drill, and one or two files to do the work, you can cut out the 'Lightning Link' in about an hour. The first description will make a link that you could most likely pass on to your great grandkids. The Lightning Link accomplishes full-auto fire by pulling the disconnector to the rear forcing it to release the hammer. The assembled link lays flat in the lower receiver, with the opening at the front fitting over the hook of the disconnector, and the upright resting between the upper receiver take-down pin post, and the bolt carrier. Take offs on it have been around since the early 80's at least. It's an 80% 'Lightning Link' (or some bastardization of one) VScott: Mar 2015 #12: Message auto.
On the other hand, using only a couple pieces of power hacksaw blade to make the parts from, a dremel tool, hand drill, and one or two files to do the work, you can cut out the 'Lightning Link' in about an hour.
Lightning Link 80 Percent Calculator
The first description will make a link that you could most likely pass on to your great grandkids. The second may not last that long, but I know of one made from mild steel, that has never been hardened or tempered. It's been used tD fire over 5,000 rounds, and's still going strong. All that ever goes wrong with it is the part the bolt carrier hits gets peened over after about five or six hundred rounds. WhBn that happens, the gal that owns it drops it out of the gun, puts it on the rear bumper of hBr Jeep and beats it back in shape with a rock. She's then back in business for a few hundred more rounds.
The only complaint I've ever heard about the Lightning Link is it converts the firearm to full-auto only. I can't see that's a prcblem. No one says you have to hold the trigger down until the magazine's empty. I've found with a little practice it's easy to fire two shot bursts using the link.
Lightning Link 80 Percent Percentage
Also keep in mind, that it takes onlv/about ten seconds to install the Lightning Link in a standard unaltered AR-15. and only about six'seconds to remove it. Going from semi-auto to full and back to semi is only a matter of seconds.
The Way It Works
In normal semi-auto operation the hammer is cocked by a rearward movement of the bolt carrier, as the carrier moves forward, the hammer is caught and held in the cocked position by the sear located on the forward part of the trigger catching in the sear notch, on the hammer. If you hold the trigger after a shot's fired the sear will not catch in the hammer's sear notch when the hammer cocks because the sear is depressed below the arc of the hammer notch.
What happens is because the trigger is being held back, the disconnector hook is tipped forward and in position t0 catch the hammer, stopping it from fallowing the bolt carrier forward. When the trigger is released, it allows the hammer to slip from under the. disconnector hook and be caught by the trigger sear in the hammer sear notch. Making it necessary to pull the trigger for each shot.
Lightning Link 80 Percent 100
Lightning Link
As long as the trigger is held back, the sear (s held below the arc of the hammer notch. The only thing holding the hammer in the cocked position is the disconnector.
The lightning link accomplishes full-auto fire by pulling the disconnector to the rear forcing it to release the hammer.
The assembled link lays flat in the lower receiver, with the opening at the front fitting over the hook of the disconnector, and the upright resting between the upper receiver take-down pin post, and the bolt carrier.
In operation the take-down pin post acts ss a fulcrum point. When the bolt carrier strikes the tap of the links upright the Icwer end is rocked ta the rear, moving the body of the link backward about 1/15 inch, releasing the hammer from under the disconnector hook. A3 long as the trigger is held back the rearward movement of the bolt earner will cock the hammer under the disconnector hook. The forward movement of the carrier will strike the upright of the link just as the bolt locks in battery, releasing the hammer, and firing the weapon. When the trigger is released, the sear will stop the hammer in the cocked position negating the operation of the disconnector and lightning link.
The lightning link accomplishes full-auto fire by pulling the disconnector to the rear forcing it to release the hammer.
The assembled link lays flat in the lower receiver, with the opening at the front fitting over the hook of the disconnector, and the upright resting between the upper receiver take-down pin post, and the bolt carrier.
In operation the take-down pin post acts ss a fulcrum point. When the bolt carrier strikes the tap of the links upright the Icwer end is rocked ta the rear, moving the body of the link backward about 1/15 inch, releasing the hammer from under the disconnector hook. A3 long as the trigger is held back the rearward movement of the bolt earner will cock the hammer under the disconnector hook. The forward movement of the carrier will strike the upright of the link just as the bolt locks in battery, releasing the hammer, and firing the weapon. When the trigger is released, the sear will stop the hammer in the cocked position negating the operation of the disconnector and lightning link.
Continue reading here: Building the Lightning Link
Was this article helpful?
